Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Dallas?
Gate repair in Dallas typically costs between $185 and $485 for most common fixes in 2026, with a service call fee of $75 to $125 that’s usually credited toward the repair if you proceed. Full gate motor replacement lands higher, usually $650 to $1,750 depending on the opener brand and gate weight. If you’re calling about Gate Repair for a gate that won’t open, a dead keypad, or a hinge that’s sagging, you’ll likely fall somewhere in that first range.
Those are real numbers we quote at the door, and they’re the same numbers we hand you in writing before we touch a single bolt. No vague “it depends” followed by a surprise invoice at the end. At Warden Gate Repair Dallas, our technicians are factory-trained on nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means the part we diagnose and the price we quote are both right the first time. Here’s exactly How Much Does Gate Repair Cost in Dallas, TX? (2026 Price Guide), what drives the number up or down, and how to avoid paying for a problem you don’t have.
Gate Repair Cost Breakdown (2026)
Every gate repair in Dallas falls into one of a handful of categories. The table below reflects what we’re seeing across neighborhoods from Lakewood to Preston Hollow to Oak Cliff in 2026. Prices include parts and labor unless noted.
| Repair Type | Typical Cost Range (Parts + Labor) | Notes |
|---|---|---|
| Service call / diagnostic visit | $75 – $125 | Credited toward repair if you approve the work. Free estimate by phone always. |
| Hinge replacement (single, welded steel) | $185 – $340 | Price climbs if the post is damaged or the gate is oversized. |
| Gate sag correction / frame re-alignment | $220 – $410 | Common on older wrought-iron gates in the M Streets and East Dallas. |
| Keypad or receiver replacement | $160 – $310 | Includes programming. Works with LiftMaster, DoorKing, Mighty Mule, and others. |
| Gate motor replacement (residential swing or slide) | $650 – $1,450 | Mid-range for most residential operators. |
| Gate motor replacement (heavy-duty commercial or estate gate) | $950 – $1,750 | FAAC, BFT, and Viking hydraulic operators run higher. |
| Photo-eye sensor replacement | $140 – $260 | Safety sensor; required for automatic gate function. |
| Track adjustment or roller replacement (slide gates) | $250 – $480 | Common in North Dallas and Richardson-area properties with long driveways. |
| Full control board replacement | $300 – $620 | Board only; excludes motor. Common on Lightning-struck systems. |
| Complete gate system install (motor, arms, keypad, sensors) | $2,200 – $5,500 | Full replacement package, including programming and testing. |
What drives these numbers in Dallas specifically? Three things, mostly. First is gate weight and length: a 14-foot iron gate in Highland Park needs a bigger motor and stronger hinges than a 6-foot wooden driveway gate in Mesquite. Second is access: if the post is set in stone or concrete, Hinge & Post Repair becomes concrete work, and that’s labor time. Third is brand and age of the opener. A 20-year-old FAAC unit might need a full board and motor swap, while a 5-year-old LiftMaster often just needs a sensor or capacitor. We give you the written price before any work starts, so you know the exact number either way.
What Affects Gate Repair Pricing in Dallas
- Gate material and weight. Wrought iron, steel, and composite gates stress different hardware. A heavy steel sliding gate needs a heavier-duty roller track and a stronger motor, which pushes both parts and labor higher. Most Dallas proper homes built before 2000 have steel or iron.
- Opener brand and parts availability. LiftMaster and Linear parts are widely stocked, so repairs run faster and cheaper. Viking and FAAC hydraulic parts sometimes need to be ordered from a regional distributor, adding a day or two and a little shipping cost. We carry stock for all nine brands we service.
- Age of the system. Gates installed in the 2000s, before the housing boom, often have degrading solder joints on control boards and corroded limit switches. Once a system hits 12 to 15 years, a partial repair may not make economic sense compared to a new motor and board. We’ll tell you honestly which side of that line your gate falls on.
- Location and driveway setup. Long driveway slide gates, common in Lake Highlands and Far North Dallas, use more track and more rollers. Repairing a binding slide gate can require realigning 20 to 30 feet of track, which is labor-intensive. A simple swing gate on a short post is faster.
- Storm and surge damage. North Texas gets serious lightning. We replace more control boards in April and May after spring storms than any other time of year. If you don’t have a surge protector on your gate circuit, the odds of a board failure go up significantly.
- The technician’s skill level. A gate is not a garage door. A general handyman who “does gates on the side” often misdiagnoses a $200 sensor issue as a $1,000 motor failure. Our techs are factory-trained and brand-certified, and you’ll know their name and see their photo before they arrive.
How to Save on Gate Repair
You don’t save money on Gate Repair Near Me in Dallas, TX by finding the cheapest tech. You save by catching problems early and not paying for misdiagnosis. Here’s what actually works in Dallas:
- Call before the gate stops moving entirely. A gate that’s slowing down, grinding, or hesitating is telling you something. A $50 capacitor or a $30 roller caught early prevents a $700 motor replacement later. Every week we see gates that limped along for months before they died.
- Ask for the written price before work starts. If the company won’t put a number on paper, you’re the one carrying the risk. At Warden, the written price is the rule, not a favor. And if the repair isn’t right, the 365-Day Done Right Promise means a free return visit to make it right. That’s our guarantee in writing on every invoice.
- Don’t skip the small fixes. Hinges, rollers, sensors, and keypads are all under $500. A full gate replacement often runs $2,200 and up. Most gates in Dallas can be repaired for years before replacement is genuinely necessary. We’ll tell you plainly when repair has become throwing good money after bad.
- Get a free phone estimate. Call (361) 322-4460. A live person answers, 24/7, not a voicemail or a chatbot. We’ll give you a straight estimate by phone, send the tech’s name and photo before arrival, and deliver a written price before any work starts. If you don’t like the number, you don’t pay it. That’s the whole arrangement.
And a note on the name, since it comes up: a warden is someone trusted to watch over a place and keep it secure. That’s the entire idea behind Warden Gate Repair Dallas. The technicians we send are background-checked, identity-verified, and photo-badged. They’ll show you that ID at the door before stepping onto your property. That’s the Threshold Standard, and it’s non-negotiable on every visit, for every customer, whether you’re home alone, home with small kids, or recovering from surgery and cautious about who you let in.
Step-by-Step: What Happens When You Call Warden for Gate Repair in Dallas
If you’ve never hired a gate repair company before, here’s exactly how it goes with us, so nothing about the process is a surprise:
- You call (361) 322-4460. A live person picks up, 24 hours a day. You describe what the gate is doing, or not doing. We’ll give you a ballpark range over the phone and set a visit time that works.
- You get your tech’s name and photo. Before arrival, we send you the name, photo, and background-check details of the exact technician coming to your door. You’ll know exactly who to expect, down to the face.
- The tech diagnoses in person. On arrival, the technician shows a photo ID badge at the door. Then they inspect the gate, motor, wiring, and sensors, and explain the actual fault in plain words: a capacitor, a worn hinge, a toasted control board, whatever it is.
- You receive a written price. Before any work starts, you get the full cost on paper. No surprise line items at the end. If you don’t want the repair, you pay only the service call fee, and that’s the end of it.
- The repair gets done right. Factory-trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, the tech completes the repair, tests the full cycle repeatedly, and walks you through what was replaced.
- You’re covered for a year. Every repair includes the 365-Day Done Right Promise: if the repair isn’t right, we make it right, including a free second visit. That’s the entire guarantee, in writing.
That’s the process. It works the same whether you’re in Lakewood, Oak Lawn, Kessler Park, or anywhere else in Dallas. And it works because we don’t outsource the hard part: knowing exactly who shows up and exactly what the job costs.
How Much Does Gate Motor Replacement Cost in Dallas?
Replacing a gate motor in Dallas runs $650 to $1,450 for most residential swing or slide gates in 2026. Heavy-duty estate gates and commercial operators, which use hydraulic systems from FAAC, BFT, or Viking, run $950 to $1,750. That price includes the new motor, the labor to remove the old unit, wiring and programming, and a full test of the safety sensors and cycle limits.
The gate motor, which is the box that slides or swings your gate automatically, fails in predictable ways. Capacitors go first, usually after 8 to 10 summers of Dallas heat. Control boards go next, especially after a lightning storm takes out the circuit. The actual motor windings often outlast both. So before you spend $1,200 on a full motor replacement, it’s worth having a brand-certified tech check the smaller parts. We’ve saved plenty of Dallas homeowners $800 by replacing a $65 capacitor instead of a motor. And if the motor genuinely is dead, you’ll know because we’ll show you the failed part and give you the written price for a new one before any work begins. Call (361) 322-4460 for an exact quote, free over the phone.
Is It Cheaper to Repair or Replace a Gate?
Repair is cheaper than replacement in nearly every case, and the math isn’t close. A hinge replacement is $185 to $340. A full gate replacement, including the structure, posts, hardware, motor, and programming, starts around $2,200 and goes up from there. For most Dallas gates, even a 20-year-old iron gate can be restored with new hinges, straightened frame sections, and new hardware for under $800. Replacement only makes sense when the gate frame itself is rusted through, the posts have shifted in the foundation, or the motor and control systems have all failed simultaneously. We’ll tell you if you’re at that point. Many companies will nudge you toward replacement because the invoice is bigger. We won’t, and we’ll show you the repair math in writing first. That’s the honest read from a team that’s been doing gate-specific work since 2008 as part of the Threshold Group family, with Cole Rafferty leading the Dallas operation.
Can You Fix My Gate the Same Day?
Yes, in most cases. Warden Gate Repair Dallas maintains local stock on common parts for all nine brands we service, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Hinges, rollers, sensors, keypads, capacitors, and many control boards are on our trucks when we pull up. Complex hydraulic motor replacements from FAAC or BFT may need parts ordered from the regional distributor, which adds one to two business days. The live person you talk to at (361) 322-4460 will tell you honestly whether your repair is same-day or next-day, and you’ll get the written price either way before we start.
FAQs – Gate Repair Cost
How much does gate repair cost in Dallas?
Most gate repairs in Dallas cost between $185 and $485 for common fixes like hinge replacement, sensor repair, keypad replacement, or track adjustment. Gate motor replacement runs $650 to $1,750 depending on the opener brand and gate weight. A service call fee of $75 to $125 is standard and is credited toward your repair. Call (361) 322-4460 for a free phone estimate with a real price range.
How much does a gate motor cost in Dallas?
A residential gate motor replacement in Dallas costs $650 to $1,450, including labor, wiring, and programming. Heavy-duty or hydraulic operators from brands like FAAC, BFT, and Viking run $950 to $1,750. The brand, gate weight, and driveway configuration all affect the price, and you’ll get the exact written number before any work begins.
Is gate repair worth it, or should I replace the gate?
Repair is worth it in most cases. A $185 hinge repair or $300 control board replacement fixes the vast majority of gate failures, while full replacement starts around $2,200. Replace only when the frame is rusted through, posts have shifted, or the motor and controls have all failed. We’ll give you the straight arithmetic on both options, in writing.
Why does my gate motor click but not move?
That click usually points to a failed capacitor, which costs $60 to $110 to replace, or a stripped gear inside the motor, which runs $180 to $320. It can also be a low-voltage issue or a control board fault. A trained tech can diagnose it in a visit. Call (361) 322-4460 and we’ll walk you through what the sound likely means before we even schedule.
Do you charge for estimates?
Phone estimates are always free. The on-site diagnostic visit costs $75 to $125, which is credited toward your repair if you approve the work. You’ll get a written price before any work begins, and if you decide not to proceed, the service call fee is all you pay.
What brands do you service in Dallas?
We repair and service nine major gate and opener brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your opener is one of these, our factory-trained techs have the correct parts and programming knowledge. If it isn’t, we’ll tell you so honestly over the phone rather than schedule a wasted visit.
Still have a question about gate repair cost in Dallas? Call (361) 322-4460. A live person answers, 24/7. You’ll get a straight price range, a free estimate, and if you book, the name and photo of your technician before they ever knock on your door. Written price first. Always. That’s the Warden way.
Pricing reflects the Dallas market as of 2026. Warden Gate Repair Dallas offers free estimates – call (361) 322-4460.
Written by Cole Rafferty, Owner at Warden Gate Repair Dallas, serving Dallas since 2008.
What Our Customers Say
"Good repair on our gate operator board. Waited a couple days for the board to arrive, but he checked in. Works perfectly now."
- Monica P."Fair price and no pushing a whole new gate when all I needed was a new motor capacitor."
- Shirley A."Slide gate stopped halfway and the motor just hummed. Tech showed his ID, tested the limit switch and found a worn roller wheel. Replaced both and the gate glides again."
- Curtis B.