FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Dallas Owner’s Guide

We stock and install FAAC-compatible hinge and roller kits across Dallas, with most replacements running $185 to $390 installed depending on your gate’s weight and how many hinge points need attention. We keep the most common FAAC hinge and roller assemblies on the truck, so a same-day swap is realistic for most single and double swing gate jobs in Dallas neighborhoods like Lakewood, Preston Hollow, and Bishop Arts. Most owners call us because the gate started dragging on one side, or they heard a grinding sound that got worse over a couple of weeks. That drag is usually a roller that’s stopped rolling, and the hinge above it is now carrying weight it was never meant to hold.

Call (361) 322-4460

Which FAAC Models This Applies To

This page covers hinge and roller replacement for FAAC swing gate operators and the gate leaves they drive, most commonly the 390, 391, 400, 412, 415, 750, 760, 770, and 884 series. FAAC hinges on residential Dallas gates are typically bolt-on steel or cast assemblies, and the rollers ride in a track or on a strike plate at ground level. The compatibility gotcha we see all the time: FAAC 400-series hinges use a different bolt spread than the 770-series, even though both sit on similar-looking steel posts. Measure center-to-center on the hinge mount before ordering anything. A hinge that’s 4 inches tall is not automatically a match for a 4-inch gate post. We’re an independent Dallas service provider, not a FAAC affiliate, but we work with FAAC OEM parts and proven aftermarket equivalents daily. For most Dallas homeowners, OEM is the sensible choice on hinges because the bolt pattern and steel gauge are exact. Aftermarket rollers are usually fine, and cost about 30% less.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate drags or scrapes near the latch side. The roller under the outer end has worn flat or seized. The hinge is now carrying vertical weight it wasn’t designed for, and it will wear oval fast.
• A grinding or squealing sound when the gate moves. That’s metal-on-metal from a roller that stopped spinning. The bearing is gone. Grease won’t bring it back.
• The gate visibly tilts or sags toward one side. A worn hinge pin or elongated hinge hole lets the leaf drop. You’ll see a wider gap at the top of the post than at the bottom.
• The FAAC opener strains or faults out mid-cycle. When hinges and rollers bind, the operator works harder. On FAAC 390 and 400-series boards, you might see the operator stop and reverse, or throw an error.
• The gate won’t latch properly anymore. As the leaf sags, the latch no longer lines up with the strike. Homeowners sometimes adjust the latch instead of addressing the real problem underneath.

Replacement Cost & What’s Included

In Dallas, expect to pay roughly $185 to $390 installed for FAAC hinge and roller replacement. A single roller swap on a lightweight driveway gate runs at the lower end. A full hinge and roller set on a heavy steel gate, especially one that needs shimming or post work, lands at the upper end. Every quote includes the parts, the labor, and the adjustment of the gate so it swings level and latches cleanly. You’ll get a written price before anything comes off the gate. No line items added at the end. The work is covered by the 365-Day Done Right Promise: if the repair isn’t right, we make it right, and a return visit is free.

Key Takeaways

• FAAC hinge and roller replacement in Dallas typically runs $185 to $390 installed.
• Same-day service is usually possible; we keep common FAAC hinges and rollers on the truck.
• OEM hinges are the smart call for bolt-pattern accuracy; aftermarket rollers are a reasonable money-saver.
• Your written price is locked before we start, and every job carries the 365-Day Done Right Promise.

DIY or Call Us?

If the gate is sagging, you can safely check the obvious: look at the gap between the gate leaf and the post, and see whether the roller makes contact with the ground plate. That’s worth knowing before you call us. But swapping FAAC hinges on a heavy gate is not a one-person weekend project. A full steel driveway gate under tension can shift suddenly when a hinge is unbolted, and that’s a real pinch and crush hazard. We’re not being dramatic; we’ve repaired DIY hinge jobs where the gate dropped and twisted the remaining hinge plates. Tell me what it’s doing wrong, and I’ll tell you what it costs to fix it, before I touch a thing. Call (361) 322-4460 and you’ll get a straight answer, a written price, and a tech whose name and photo you’ll know before we arrive.

FAQs