FAAC Gate Motor Replacement Nationwide

FAAC Gate Motor Replacement: The Dallas Owner’s Guide

FAAC gate motor replacement in Dallas typically runs $850 to $1,800 installed, depending on the model and whether you need the full operator or just the control board. We stock FAAC-compatible motors and parts on our trucks, so most replacements are done the same day we arrive. You’ll know it’s time when your gate groans, stalls halfway, or simply stops responding to the remote altogether.

Call (361) 322-4460

Here’s the scene we see most often: a homeowner in Lakewood or Preston Hollow hits the clicker, hears a hum or a click, and the gate doesn’t budge. Or it opens but won’t close without a fight. That’s when FAAC owners start searching for a replacement motor and land here. Good. Let’s get into the details that actually matter for your FAAC.

Key Takeaways

• We carry FAAC OEM and quality aftermarket replacement parts on Dallas service trucks
• Most FAAC gate motor swaps take 90 minutes to 3 hours on site
• Written price before we touch anything, every time
• Every replacement is covered by our 365-Day Done Right Promise

Which FAAC Models This Applies To

We replace motors across the FAAC residential swing and slide gate line: the 400 series (402, 412, 422), the 760/770 series for heavier swing gates, the 391 and 844 slide operators, and the S418 and S450H hydraulic units that some Dallas homes still run. We are an independent service provider, not affiliated with FAAC, but our techs have opened enough of these units to know which revision you have by the label alone.

Here’s the compatibility gotcha most Dallas owners don’t know: FAAC motors are not universal. The 402 and 412 both drive swing gates, but the 412 is built for longer leafs and higher cycle counts. Swap the wrong one in and you’ll be back to replacing it within two years. The control board is just as picky. A 455D board will run a 402 motor, but it won’t talk correctly to a 760. We identify the exact series by the metal nameplate riveted to the motor housing, plus the board part number stamped on the PCB. That’s the part match.

On OEM versus aftermarket: FAAC OEM parts carry their usual quality, but lead times can stretch when the distributor is out of stock. We keep both OEM and tested aftermarket replacements on hand for the most common Dallas models. The aftermarket motors we install use the same gear ratios and mounting footprints, and we’ll tell you honestly which one makes sense for your gate’s weight, cycle count, and age before you spend a dollar.

Signs Your FAAC Gate Motor Replacement Is Failing

Tell me what it’s doing wrong, and I’ll tell you what it costs to fix it, before I touch a thing. That’s the rule around here. Here’s what we hear from Dallas FAAC owners before a motor replacement.

• Gate hums but doesn’t move: The motor gets power, but the capacitor or the gear train has failed. Common on FAAC 402s after six to eight Dallas summers. The motor is trying; it just can’t turn the output shaft.
• Gate opens fine but creeps or drops when closing: The motor’s internal brake or the operator’s limit switch is wearing out. On FAAC swing arms, this also points to a stripped worm gear inside the gearbox.
• Remote works intermittently, then stops: Before you blame the motor, check the receiver board and antenna. But if the motor’s thermal overload keeps tripping, the motor itself is pulling too much current. That’s a replacement signal, not a reset signal.
• Burning smell near the operator box: That’s the motor windings or the capacitor overheating. Shut the breaker off and call us. A burned FAAC motor can take the control board down with it if it shorts.
• Gate moves at half speed or shudders: The drive gear or the motor bearings are worn. In Dallas, our freeze-thaw cycles in February and our 100-degree July afternoons both shorten bearing life. Shuddering today becomes a locked gate tomorrow.

If you’re hearing any of these, the motor is on its way out. The question is whether it lasts another month or another week. Most don’t give you much warning at the end.

Replacement Cost & What’s Included

FAAC gate motor replacement in Dallas lands between $850 and $1,800 installed. The range depends on your model, whether we’re replacing the motor head only or the motor and control board together, and how much wiring or mounting correction the old installation left behind. Here’s the honest breakdown.

• FAAC swing motor replacement (402, 412, 422): $850 – $1,250 installed
• FAAC heavy-duty swing motor (760, 770 series): $1,150 – $1,550 installed
• FAAC slide motor replacement (391, 844): $950 – $1,400 installed
• Hydraulic FAAC operator (S418, S450H): $1,300 – $1,800 installed

Every one of those prices includes the motor, the labor to remove the old unit and mount the new one, wiring tie-ins, limit setup, and a full cycle test before we leave. We write the price down before we start. No surprise line items at the end. Ever. And the replacement is covered by our 365-Day Done Right Promise: if the motor or our install fails within the year, the return visit is free. Cole Rafferty and every tech on our crew stand behind that in writing.

DIY or Call Us?

FAAC gate motors run on 120V or 240V at the board and can deliver 300 to 800 pounds of force at the gate leaf. That combination can injure you. This is not a part we recommend swapping on a Saturday afternoon with a YouTube tutorial open. If you want to check something before you call, here’s what’s safe: confirm the breaker is on, check that the manual release lever isn’t engaged, and look for visible damage to the arm or track. Stop there.

The dangerous part is the electrical and the stored torque. A charged capacitor inside a FAAC operator can hold voltage even after the breaker is off. And a swing gate under tension from a worn gearbox can snap back when you unbolt the motor. Our techs do this work with the power locked out and the gate physically secured. If you’d rather not risk it, call (361) 322-4460 and we’ll send someone who does this every week in Dallas neighborhoods like Lakewood, White Rock, and Bishop Arts.

FAQs

Call for a FAAC Gate Motor Replacement in Dallas

If your FAAC gate is groaning, stalling, or dead, call Warden Gate Repair Dallas at (361) 322-4460. We’ll send you the name and photo of the tech before they arrive, every time. Your written price comes before any work starts. And your replacement carries the full 365-Day Done Right Promise. That’s how we’ve worked since 2008, and it’s the only way we’ll do it in Dallas.

Written by Cole Rafferty, Owner, Warden Gate Repair Dallas at Warden Gate Repair Dallas, serving Dallas and nearby areas.