Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Dallas?
Gate parts and welding repairs in Dallas typically run between $225 and $1,400, with most welded gate frame repairs landing in the $350 to $650 range. A simple hinge replacement or gate wheel swap costs $150 to $300, while full weld repair on a sagging steel driveway gate runs $450 to $900 depending on the extent of the damage. If you’re calling about a broken gate in Lakewood or Preston Hollow, expect to pay more for wrought iron work than for chain-link or aluminum.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what we actually quote on welded gate work across Dallas. These are real ranges from jobs we’ve priced in neighborhoods from Oak Cliff to Far North Dallas, and they reflect both parts and the labor to install them correctly.
| Repair Type | Typical Dallas Price Range | What It Includes |
|---|---|---|
| Hinge replacement (per hinge) | $75 to $250 | New steel or iron hinge, welding, alignment |
| Gate wheel or caster replacement | $85 to $175 | New wheel, mounting bracket, weld if needed |
| Wrought iron gate frame repair | $350 to $700 | Cracked frame weld, reinforcement plate, touch-up |
| Steel driveway gate weld repair | $450 to $900 | Full frame repair, gussets, grinding, paint prep |
| Aluminum gate weld | $250 to $500 | Aluminum-specific TIG welding, frame straightening |
| Gate post reinforcement | $200 to $550 | Post sleeve, base plate weld, re-anchoring |
| Full gate frame rebuild | $800 to $1,400 | Cut out failed sections, rebuild frame, rehang |
| Ornamental iron restoration (per section) | $150 to $400 | Replace pickets, scrollwork, weld and grind smooth |
| Gate motor bracket fabrication | $125 to $350 | Custom bracket weld for opener arm or slide gear |
Several things push a welded gate repair toward the higher end of those ranges. If the gate has been dragging for months, the frame is often cracked in multiple places, not just one. If rust has compromised the bottom rail, you’re not welding it – you’re cutting it out and replacing a section of steel. If the post shifted, the gate has to be un-hung, the post reset or reinforced, and the gate re-hung. That’s a bigger job than a hinge swap, and it should be priced that way.
What Affects Gate Parts & Welding Pricing in Dallas
- Material type. Wrought iron and ornamental steel take longer to weld cleanly than basic chain-link. Aluminum is a different skill entirely – it requires TIG welding equipment and a tech who actually knows aluminum’s heat sensitivity. Most gate companies in Dallas don’t offer aluminum welding at all.
- Where the crack or failure is. A broken hinge plate at the top corner is accessible and quick. A cracked frame rail at the bottom hinge means the gate has to be lifted off its hinges entirely. That adds labor, and labor is most of the cost on weld work.
- Gate weight and size. A 16-foot steel driveway gate in a neighborhood like Bluffview is heavy. Handling it safely takes at least two people and often a lift. A small pedestrian gate in a North Dallas alley is a one-person job.
- Dallas soil movement. This is the factor nobody puts on their website. North Texas clay soil expands and contracts dramatically, and we see the effect on gate posts every week. A post that was plumb in 2020 leans by 2025, which shifts the entire gate, which stresses every weld point until one fails. If your repair quote includes post rehab, that’s the clay talking.
- Powder coat or paint matching. A structural weld is one thing. Making the repair disappear is another. Matching a faded black powder coat on a 12-year-old gate in Highland Park takes prep work, sanding, and color blending that adds $100 to $200 to the bill.
- Emergency timing. A gate that won’t close at 2 a.m. in a neighborhood with a high property-crime awareness isn’t a “next week” fix. Same-day and after-hours weld service costs more, and it should.
How Much Do Common Gate Parts Cost in Dallas?
Beyond welding, here’s what individual gate hardware parts run in the Dallas market as of 2026. These are the prices you’ll see on a written quote from any reputable gate company, and they’re worth knowing before you agree to anything over the phone.
- Heavy-duty gate hinges (steel, weld-on): $30 to $90 per hinge
- Adjustable gate hinges (bolt-on): $25 to $60 per hinge
- Cantilever gate rollers: $75 to $225 per assembly
- V-track slide gate wheels: $40 to $110 per wheel
- Gate latch hardware (solenoid-compatible): $45 to $150
- Gate lock and keypad-ready strike: $60 to $250
- Gate opener arm (swing gate): $150 to $450
- Slide gate rack and pinion gear: $80 to $300
- Loop detector for vehicle exit: $60 to $180
- Photo-eye safety sensor pair: $40 to $110
Parts prices don’t tell the whole story. Installation is where a cheap part becomes an expensive problem. A $35 hinge welded incorrectly will tear out in six months. A $90 hinge installed by someone who takes the time to align the gate properly lasts a decade. When you see a company advertising bottom-dollar part prices, ask what their labor rate is and who’s doing the install.
What Should You Actually Pay for Welding on a Gate in Dallas?
Welding itself, billed as a standalone service, runs $95 to $185 per hour in Dallas as of 2026. Most gate weld repairs take between one and four hours of actual torch time. A simple crack fill at an accessible location might be one hour. A full frame reinforcement with gussets, grinding, and repainting prep might be four.
Mobile gate repair companies typically include their travel in the hourly rate or add a $60 to $125 trip fee. Shops with a physical location in Dallas proper – versus companies driving in from outside the metro – often price weld work slightly higher because their overhead is higher, but you’re also dealing with a company that has an address you can find.
Here’s a practical example. In Oak Lawn and the M Streets, we regularly see pedestrian gates from the 1990s with failed bottom hinges and minor frame cracks. That job, done properly with a new weld-on hinge, frame repair, grinding, and paint matching, usually lands at $380 to $520. A full-size driveway gate with a cracked mid-rail and two failed hinges runs $650 to $950. If you get bids below those numbers, ask to see the welder’s work. If you get bids far above, ask what’s driving the extra cost.
How to Save on Gate Parts & Welding
Saving money on welded gate repair isn’t about finding the cheapest welder. It’s about not paying for the same repair twice.
- Fix small problems before they become frame cracks. A $40 gate wheel replacement today becomes a $700 frame repair after a year of dragging. Listen for grinding, clunking, or a gate that’s suddenly heavier to push.
- Ask for a written price before work starts. This is the single biggest money-saver in gate repair. A verbal estimate is not a price. A written price with a clear scope means no $400 surprise line items at the end.
- Bundle hinge and wheel work. If the gate needs hinges and a caster replaced, doing both at once saves $75 to $125 in trip and setup labor versus two separate visits.
- Ask about the guarantee in writing. A weld that fails in four months because the hinge wasn’t prepped correctly shouldn’t cost you a second repair fee. Before you hire anyone, ask what happens if the repair fails.
- Maintain the gate opener separately. The weld and the motor are different systems. If the opener is pushing a misaligned gate, the opener fails early and the frame stress continues. Fix the gate geometry first, then address the motor.
We give free estimates on welded gate and gate parts work across Dallas. Call (361) 322-4460 and we’ll quote the job in writing – no pressure, no vague ranges, just a number you can compare.
How Warden Gate Repair Prices and Performs Welded Gate Repairs
Our welding and gate parts service is built around one idea: you should know exactly what you’re paying before the torch comes out. Cole Rafferty, who leads Warden Gate Repair Dallas, set the policy that every weld job gets a written price first. No exceptions. You see the number. You approve it. Then the work begins.
The tech who arrives for your weld repair isn’t an anonymous contractor. Every Warden technician is background-checked, identity-verified, and photo-badged under the Threshold Standard – and you get their name and photo sent to you before they knock. The person at your gate is the person we said was coming.
Our welding work carries the 365-Day Done Right Promise: if the repair isn’t right, we come back and make it right at no charge. That’s not a slogan. It’s in writing on every job.
We’re factory-trained on gate systems from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – because a weld repair often intersects with gate opener hardware. You don’t want a welder who can’t tell the difference between a swing arm bracket and a slide gate rack. We handle both sides of the gate.
Steps We Take on a Weld Repair Job
If you’ve never had welded gate work done before, here’s how a typical repair goes with our team.
- Call and describe the problem. A live person answers at (361) 322-4460 – 24/7, not a voicemail tree. You’ll describe what you’re seeing: sagging gate, cracked frame, broken hinge, dragging wheel.
- We schedule a site visit. For weld work we need to see the gate in person. Weld repairs are structural, and guessing from photos leads to under-quoting and surprises.
- You get a written price. After inspection, we give you the repair scope and dollar amount in writing. Compare it to our published ranges. If it matches, good. If you want a second opinion, the price doesn’t change because you took time to think.
- Weld repair and parts replacement. The tech performs the frame repair, hinge replacement, wheel swap – whatever the written scope said. We grind, smooth, and prep surfaces properly.
- Paint match and finish. Where the gate had coating, we blend the repair area to match as closely as the gate’s current condition allows. It won’t be invisible on a 15-year-old gate, but it won’t look like a fresh scar either.
- Re-hang and test. The gate goes back on its hinges, swings or slides true, and we cycle it through its full range before we leave. Your photo-badged tech confirms the gate operates correctly with you watching.
FAQs – Gate Parts & Welding Cost
How much does it cost to weld a broken gate frame in Dallas?
Welding a broken gate frame in Dallas costs $350 to $900 depending on the number of cracks and the frame’s material. A single crack in an accessible location runs $350 to $450, while a frame with multiple stress fractures plus reinforcement plates will push toward $900. Call (361) 322-4460 for a written quote – the estimate is free.
Is it cheaper to weld a gate or replace it?
It’s cheaper to weld and reinforce a gate when the repair cost stays under 60% of replacement. In Dallas, a new steel driveway gate runs $1,800 to $4,500 installed, so a $700 frame repair makes sense on most gates under $2,000 in replacement value. Call (361) 322-4460 and we’ll give you a straight answer on which makes sense for your specific gate.
How much do gate hinges and wheels cost to replace in Dallas?
Gate hinge replacement in Dallas runs $75 to $250 per hinge installed, and gate wheel or caster replacement runs $85 to $175 per wheel installed. Frequent drag-gate repairs in the M Streets and Lakewood often require both hinges and wheels at once, which typically lands at $300 to $600 total. Call (361) 322-4460 for a free estimate on your gate.
Can you weld an aluminum gate in Dallas?
Aluminum gate welding in Dallas costs $250 to $500 for typical frame repairs, and yes – we do aluminum TIG welding, which most gate companies don’t offer. Aluminum requires different equipment and training than steel, and a poor aluminum weld can fail suddenly rather than gradually. Call (361) 322-4460 to confirm your gate is aluminum and get a quote.
How soon can someone weld my gate in Dallas?
Same-day weld service in Dallas is available for urgent cases, and our phone line is staffed by a live person 24/7. Standard scheduling is typically within 48 to 72 hours. Weld work requires dry conditions, so if it’s raining, we’ll still give you the price and schedule the moment the gate can be worked on safely.
Do you warranty welded gate repairs?
Yes. Every weld repair from Warden Gate Repair Dallas carries the 365-Day Done Right Promise: if the repair fails within a year, the return visit is free. That’s a written guarantee on every job, not a verbal assurance. Call (361) 322-4460 for a free estimate and a written price before any work begins.
Get a Written Price Before You Weld Anything
You don’t have to guess. You don’t have to take a phone estimate as final. Call (361) 322-4460 and tell us what your gate is doing. We’ll send a photo-badged, background-checked tech to your Dallas home, inspect the gate, and hand you a written price for the weld repair or parts replacement before a single spark flies.
We service all of Dallas, from Bishop Arts to Lake Highlands, from Preston Hollow to Pleasant Grove. Our home page has more on how we work, and our Gate Parts & Welding in Dallas page covers the full scope of our weld and parts service. Live phone coverage, 24/7, 365 days a year. The person who answers is the person who can help.
Pricing reflects the Dallas market as of 2026. Warden Gate Repair Dallas offers free estimates – call (361) 322-4460.
What Our Customers Say
"Slide gate stopped halfway and the motor just hummed. Tech showed his ID, tested the limit switch and found a worn roller wheel. Replaced both and the gate glides again."
- Curtis B."Rusty chain drive got cleaned, lubed, and re-tensioned. He told me what to do each year to keep it going."
- Leon M."Gate was closing on my truck bumper. The loop detector had failed. Replaced it and adjusted the force setting."
- Dina K.